Posted on Leave a comment

Mushyluv Cameo 4 Universal pen adapter instructions

Cameo 4 Universal Pen adapter by mushyluv - installed

Silhouette Cameo 4 Universal pen adapter insertion guide
Load your sharpie from the bottom end of the adapter (where the cutting blade would normally be).
A good starting point length for the tip of your sharpie, pen, or pencil is to set the tip at the same length as the blade guard notch found on the side of your autoblade.
Mushyluv cameo 4 universal pen adapter Studio settings
For Sharpies, set force to 1 and speed to 4 as your starting point. Felt tips work well at lighter force numbers. Pencils require much heavier force.
pause symbol
If your stylus is wobbling in the cradle, pause the print job and shorten the length of your stylus.
Posted on

ez-SAB-gloves install guide

V2.0 glove install (clear)

V1.0 glove install (red)

Bring your ez-SAB-glove opening through the ring.
Bring your ez-SAB-glove™ opening through the ring.
Stretch the glove cuff evenly around the wring. This may take a few tries as you're stretching the glove material to fit the ring.
Stretch the glove cuff evenly around the wring. This may take a few tries as you’re stretching the glove material to fit the ring.
Insert your ez-SAB-port™ through the wall of your still air box.
Insert your ez-SAB-port™ through the wall of your still air box.
Orient the glove so the thumb of the glove is in a natural position. While holding the inside ring steady, begin screwing the outside port hole into your glove ring.
As you’re tightening the port into the glove ring,  the glove material is being drawn into the threads. Once the material has drawn into the threads, Stop. Now hold the outside port steady and finish tightening the port together by rotating the inside glove ring until snug.
Repeat the installation steps for both gloves sets, paying special attention to the orientation of the the thumbs on your gloves.  They should be in a natural up position. You’ve now completed the ez-SAB-glove install.
Powder your gloves
In your port kit you’ve been provided with a small amount of power. It’s best to powder your gloves before the first use.  This makes it easy to take the gloves on and off.
bleach disinfectant
Time to disinfect your Still Air Box. Add 2.5 Tbsp bleach to 1 quart (32oz) of water.  While its impossible to sterilize your SAB you can greatly reduce the chance of contamination with a simple bleach and water solution.
spray-bottle
Spray down the entire interior and lid of your SAB with your bleach disinfectant solution and allow it to stand for 5 minutes. Wipe away excess moisture with a clean paper towel.
Posted on

Tips for making a Still Air Box SAB

Mushyluv's porthole glove box kit. White. Installed in an SAB-mini still air glove box.

Begin by determining if you want your lid to be the top or bottom of your SAB. Orient your tote accordingly.

Note: Due of the rounded edges common to most totes used for SABs, It’s important you don’t install your ports any closer than 3/4″ from the edge of your tote. The cutout template makes it easy to visualize how your ports will look installed and any safe cutting distances.

Select the the distance apart for your arm ports (Relative to the floor of your SAB)

Mark the desired centers of your arm ports. You can use your cutout template to help visualize where your arm ports will fit best. Draw the port hole circle cut out guides onto your SAB with a sharpie using the template.

How do I cut out ports for my still air box?

Note: Cutting polypropylene and polyethylene totes can be a tricky. They have a tendency to crack and split when drilling or cutting. The following suggestions can help minimize  chances of splitting.

ez-SAB-port cut out template download (a preprinted template is included with your order as well.)Mushy Icon
When printing the cut out template, It’s important you tell the acrobat print dialogue to print “Actual size“. This insures the template is dimensionally correct. Test your template by placing it over your port threads.

The two options that are the least likely to cause cracking and splitting when cutting out your sab port holes:

Hot knife for cutting Still Air Box
Hot Knife sab port plastic cutter tool. (safest) #ad
4.5" 115mm still air box arm port hole saw.
4.5″ 115mm still air box arm port hole saw. (quickest) #ad

Hot Knife:

plastic build up around port hole after hot knife cut
Click to enlarge

You may notice plastic build up occurring on either side of your cut.  Once the newly cut port hole has cooled to room temp, take a razor blade or sharp utility knife and run it along the edge of your port hole.  Be especially careful not to cut yourself. The razor blade should trim off the excess leaving a noticeably cleaner edge around your port hole.

4.5″ (115mm) hole saw

When using a hole saw always make sure the tote’s surface you are drilling into is supported by wood or similar sturdy material underneath. Very important to prevent cracking.  If the hole saw binds when drilling out the arm port, stop and clear the cut of debris. Re-center your hole saw and complete the cut with the drill in reverse.

The Next safest bet in cutting out your port holes:

3.) Drill (a bunch of) tiny holes into the sharpie circle outlines you drew on your SAB. The smaller the drill bit the better and the more holes the better. Think 7/64″ or smaller on the drill bit. Be careful when drilling not to apply too much pressure to the bit.  Excessive bending of the plastic could lead to a split.

Two options:

A) Cut between the holes with a heated utility knife. Place the blade of the utility knife over a candle, cigarette lighter, or similar heat source then drag the heated knife cutting hole-to-hole until it cools and stops cutting. Re-heat the knife blade and continue the process until you’ve cut out the entire circle.

B) Clip between the holes (if you’ve drilled them close enough together) using flush cutter snips such as these: https://amzn.to/3m3xmwe (#ad)

This is a tedious process and will produce a ragged edged hole. No problem, simply clean up the hole as best you can pulling off any loose plastic bits from the process. As long as you don’t go way outside the template lines, the lip of your ez-SAB-port will cover up the ragged edges beautifully.

Install guides for optional glove port configuration :

elbow length Poly gloves (included): ez-SAB-glove install guide
Latex gloves (not included): – Latex glove install guide

Mushy IconReturn to mushroom Tips & Teks

Posted on

The ez-SAB-port™ latex glove install guide

ez-sab-port-with-latex-gloves

If you prefer you can add your own latex gloves to your ez-SAB-port™.

ez-sab-port-with-latex-gloves-002
Begin by inserting the glove ring into your latex gloves with the clamp ring pointed away from your port and into the glove.
ez-sab-port-with-latex-gloves
Next slip a 5″ or larger hose clamp over your glove until it stops against the clamp ring. This my take a few tries to get it even. Tighten the hose clamp to snug. Do not over tighten.
ez-sab-port-with-latex-gloves-003
Pass the ez-SAB-port™ through the wall of your still air box.
ez-sab-port-with-latex-gloves-004
Orient the thumb of your latex glove in a natural up position. Holding the inside steady so as not to change the orientation of your glove, hand tighten to two halves of the ez-SAB-port™ together by spinning the outside of the port by hand until it snugs tight. When finished click here.